1. High tensile vs low carbon woven wire fence: what changes?
High tensile describes the wire's strength. Woven wire describes how the fence is built. A woven fence can use either high tensile or low carbon wire. Do not compare high tensile wire with woven wire as if they were separate fence types.
Low carbon wire is easier to bend and shape by hand. High tensile wire can carry more force at the same diameter, when the grades are tested on the same basis. It needs suitable tools and sound end braces. Neither choice removes the need for a complete fence design.
| Buying question | High tensile wire | Low carbon wire |
|---|---|---|
| Wire size and strength | May meet a load requirement with thinner wire. Ask for diameter and test values. | Often uses thicker wire for a similar farm fence layout. Thickness alone is not proof of strength. |
| Handling and repair | Needs cutters, grips and repair sleeves rated for the wire. | Easier to bend around a repair, but the joint still needs a defined method. |
| Coating | Specify zinc or zinc alloy coating separately. | Specify the same coating fields for a fair comparison. |
| Post layout | Use the maker's layout for the site. | Use the maker's layout for the site. |
2. Compare rolls with the same mesh layout
Bekaert's 2025 catalog lists two DOT woven wire rolls with the same 1047-6 layout, 47-inch height, 6-inch stays, 330-foot length and Class 3 coating. Their wire sizes and weights differ:
| Catalog roll | Top and bottom wire | Filler wire | Listed roll weight |
|---|---|---|---|
| High tensile, part 259320 | 10.5 gauge | 12.5 gauge | 189 lb |
| Low carbon, part 235275 | 9 gauge | 11 gauge | 280 lb |
This is a buying comparison, not a controlled strength test: the wire sizes differ. It does not prove that every high tensile fence is lighter or stronger than every low carbon fence. These are Bekaert specifications, not KUNYU stock or test results.
3. Keep wire strength separate from fence strength
A wire test reports force or stress for that wire. A whole fence also depends on knots, joints, posts and braces. Ask whether a quoted breaking load applies to one line wire, a stay wire, a knot or a tested fence panel.
For a simple calculation, a 2.5 mm round wire has an area of about 4.91 mm². At an assumed tensile strength of 1,200 MPa, its calculated breaking force is about 5.89 kN. At 450 MPa, it is about 2.21 kN. This example shows why grade matters at the same diameter. It is not a KUNYU test result or an installation tension setting.
Do not pull a fence to its breaking load. Follow the selected roll's tensioning method. Fix weak braces or leaning end posts before adding more tension. A stronger wire cannot make up for a weak anchor.
4. Choose by animal, site and repair needs
For long cattle or deer boundaries, compare high tensile woven wire where roll handling and wire strength matter. Check the mesh near the ground, animal pressure and required height first. A stronger wire will not stop a small animal passing through a large opening.
For short runs with many bends or frequent hand repairs, low carbon wire may be easier to work with. Compare the full installed cost. Include rolls, posts, braces, tools and repair parts. Do not assume low carbon is always cheaper once those items are counted.
Horse fences need suitable mesh and safe fixing details with either grade. See our fixed knot and S-knot comparison. On slopes, agree the ground detail before setting post spacing. High tensile wire does not give permission to widen all post gaps.
5. Check tools before the first roll arrives
Tell the installer which wire grade you ordered. A cutter that works on soft wire may not suit high tensile wire. Match the cutter, wire grip and crimp tool to the stated diameter and grade. Use the sleeve maker's approved die and crimp pattern. Keep the repair parts with the batch record.
Handle each roll by its actual weight. A lighter roll can still need lifting gear. Keep people away from loaded wire while it is pulled or released. Check the end connections before stock return to the field.
Ask suppliers which wire products are included in a price. Plain wire, barbed wire and woven mesh serve different roles. A quote for one does not price the others. List each item on its own line so that missing parts are clear.
6. Put these fields on the quotation
Send KUNYU the animal use, fence height, roll length and a mesh drawing. List line, stay and knot wire diameters separately. State the wire grade or required test values, coating type and class, knot design and total quantity. Include the destination and unloading limits for FCL or LCL delivery.
Ask suppliers to quote the same drawing and coating. Then compare roll weight, test basis, packing and delivered cost. If the catalog does not show your required combination, send the specification for production review.
For coating selection, read Class 1 vs Class 3 woven wire fence. Steel grade and coating are separate choices.
Technical reference: Bekaert 2025 fencing catalog, DOT woven wire table. The roll example is attributed to that catalog; the force calculation uses stated assumptions.




